 |
| Since the development of the first aviation fuel
coalescer in 1943, Facet has been
at the forefront of aviation fuel handling. Evidence
the number of “firsts” in the aviation industry including the
two-stage filter separator; Posi-stop fuel monitor; CIF cartridge; and API
1581, Fourth Edition, Category M-100 cartridges, just to
name a few. Facet manufactures a
complete line of products for the aviation industry to ensure that clean,
dry fuel is provided every step of the way - from the refinery to
the wing tip – including: micronic prefilters, clay treater bags and
canisters, coalescer and separator cartridges with both screw base and
rod-mount, water absorbent elements (monitors) and the patented Posi-stop
PS “-2” fuses.
|
| DoD
Coalescer Cartridges are fully qualified to API/IP 1581, 5th Edition, M
Category, Type S requirements (data
sheet)
|
|
Coalescer Separator Cartridges
[top of page]
|
 |
21 and 22 Series Filter
Separator Cartridge provide long service life and
high solids holding capacity with no unloading characteristics. These
filter separator cartridges effectively remove water and solids from
fuels. |
|
|
|
|
CA Series 3 Coalescer
Cartridge by Facet
offers the finest performance available. This standard line of high flow
coalescer cartridges removes ultra-fine solids and enhances separation
of water from jet fuel. They are available in eight lengths with two
cartridge mounting styles; self-centering rod mount and screw base. The
rod mount has treated metal end caps, while the screw base are injection
molded, glass-filled nylon. This screw base material offers superior
strength and ease of maintenance -- uniform threads, no shrinkage, no
galling and no gasket to recover. |
 |
CA
Series 3 Coalescer Cartridge Datasheet
(CA11-3,
CA14-3, CA14-3SB, CA22-3, CA22-3SB, CA28-3, CA28-3SB, CA33-3,
CA33-3SB, CA38-3,
CA38-3SB, CA43-3, CA43-3SB, CA56-3, CA56-3SB) |
 |
Cartridge Installation Instructions |
5th Edition |
CAA Series 5 Coalescer Cartridge.
The Facet coalescer separator
housings equipped with CAA Series 5 coalescer and companion separators
cartridges have been tested and fully qualified to meet the performance
requirements of API Bulletin 1581, Fifth Edition,
Category C, Type S. Built for balanced fluid flow-thru and
structural strength, each CAA Series 5 coalescer cartridge is a
single-piece construction of various combined media, precisely arranged
in many layers and pleats, wrapped around a treated perforated metal
center tube -- all encased in an outer sock material. All are 6" OD
(152mm) by 3½" ID (89mm) and available in standard
interchangeable nominal lengths in increments of 14¼" (290mm) to 57¼"
(1450mm). The CAA Series 5 are available in two cartridge
mounting styles; self-centering rod mount and screw base. The rod mount
has treated metal end caps, while the screw base are injection molded,
glass-filled nylon. This screw base material offers superior strength
and ease of maintenance -- uniform threads, no shrinkage, no galling and
no gasket to recover. |
|
CAA Series 5 Coalescer Cartridge Datasheet (5th Edition)
(CAA11-5, CAA14-5 CAA14-5SB, CAA22-5,
CAA22-5SB, CAA28-5, CAA285SB, CAA33-5, CAA33-5SB, CAA38-5,
CAA-38-5SB, CAA43-5, CAA43-5SB, CAA56-5, CAA56-5SB) |
|
|
Cartridge Installation Instructions |
|
|
|
CA Series 9 Coalescer Cartridge by
Facet offers the finest performance
available. This standard line of high flow coalescer cartridges removes
ultra-fine solids and enhances separation of water from jet fuel. They
are available in nine lengths with two cartridge mounting styles;
self-centering rod mount and screw base. The rod mount has treated metal
end caps, while the screw base are injection molded, glass-filled nylon.
This screw base material offers superior strength and ease of maintenance
-- uniform threads, no shrinkage, no galling and no gasket to recover. |
|
CA
Series 9 Coalescer Cartridge Datasheet
(CA11-9,
CA14-9, CA14-9SB, CA18-9SB, CA22-9, CA22-9SB, CA28-9, CA28-9SB,
CA33-9, CA33-9SB, CA38-9, CA38-9SB, CA43-9, CA43-9SB, CA56-93,
CA56-9SB) |
|
|
Cartridge Installation Instructions |
|
|
CAA Series 9 Coalescer
Cartridge by Facet
offers the finest performance available. This standard line of high flow
coalescer cartridges removes ultra-fine solids and enhances separation
of water from jet fuel. They are available in two lengths with two
cartridge mounting styles; self-centering rod mount and screw base. The
rod mount has treated metal end caps, while the screw base are injection
molded, glass-filled nylon. This screw base material offers superior
strength and ease of maintenance -- uniform threads, no shrinkage, no
galling and no gasket to recover. |
|
|
|
CM Series DoD Coalescer Cartridges by
Facet offer the finest performance
available in aviation fuel filtration for the United States Armed
Forces. This line of high flow coalescer cartridges removes ultra fine
solids and enhances the optimum separation of water from Military Jet
Fuel. Designed specifically for the U.S. Military, these high
performance cartridges flow at a rate of 1 gallon per minute per linear
inch and directly replace the following
without any modification kit:
- NSN 4330-01-407-3548
40" length coalescer cartridge
- NSN 4330-00-983-0998
20" length coalescer cartridge
|
|
|
|
86 Series Coalescer Cartridge
by Facet offers the
finest performance available. This standard line of high flow coalescer
cartridges removes ultra-fine solids and enhances separation of water
from jet fuel. They are available in eight lengths with two cartridge
mounting styles; self-centering rod mount and screw base. The rod mount
has treated metal end caps, while the screw base are injection molded,
glass-filled nylon. This screw base material offers superior strength
and ease of maintenance -- uniform threads won't shrinkage, oxidize,
corrode or gall, while the smooth surface eliminates the need for
lubrication. |
|
86
Series Coalescer Cartridge Datasheet
(CC8685,
CC8682, CC8686, CC8688SB, CC8683, CC8689SB, CC8687, CC8690SB,
CC8652SB-1, CC8684, CC8691SB, CC8692SB) |
|
|
Cartridge Installation Instructions |
|
 |
SP Series Separator Cartridge
by Facet is a pleated
paper separator cartridge that functions primarily as a second-stage
water barrier in a two-stage filter separator system secondarily as a
final filter. Facet's distinctive
center tube design provides balanced flow, radially inward through the
cartridge. All metal components are treated to protect against
corrosion. They are available in 6" OD and six standard sizes from
11 to 33 inches nominal length with an outside inside flow. |
|
|
5th Edition |
ST Series Separator Cartridge
manufactured by Facet
are cleanable and reusable separator cartridge of the highest quality
in a variety of dimensional configurations. Teflon® coated screen is
wrapped around a treated, perforated metal shell, lock-seam folded and
secured by metal clips, then adhesive bonded to gasketed metal end caps.
Facet's distinctive Velocigard
design provides balanced flow, radially inward through the cartridge.
All metal parts are treated to resist corrosion. Maximum recommended
operating temperature is 240ºF. For compatibility in
extreme operating conditions other gasket, adhesive, and metal materials
are available. The Teflon® coated screen has very effective water repelling
characteristics assuring long, trouble-free service. They are available
in 5th Edition four different nominal OD sizes and 22 different nominal lengths with
an outside inside flow. |
|
|
5th Edition |
SS Series Separator Cartridges
are Facet's synthetic
separator cartridges and feature specially developed hydrophobic synthetic
media which offers all the permanent features of Teflon® screen,
with the ability to handle higher flow rates. Synthetic mesh is wrapped
around a treated, perforated metal shell, then adhesive-bonded to
gasketed metal end caps. Facet's
distinctive Velocigard design provides balanced flow, radially inward
through the cartridge. All metal parts are treated to resist
corrosion. Maximum recommended operating temperature is 240ºF.
For compatibility in extreme operating conditions other gasket,
adhesive, and metal materials are available. They are available in
5th Edition four different nominal OD sizes and 22
different nominal lengths with an outside inside flow.
Compare ST and SS Series Separators:
Rate Flow vs Injected Water Volume to Effect Failure |
|
|
|
|
 |
Clay Treater Cartridge The
primary purpose of clay treatment is to protect aviation fuel filtration
systems and jet fuel by removing trace quantities of surface active
agents (surfactants), color and additives commonly found in fuel. Facet's
specially selected Attapulgus clay greatly resists water saturation and
provides maximum surfactant adsorptivity and filtration area found in
clay treater cartridges. |
|
|
|
|
 |
21 and 22 Series Filter Cartridges are
designed for Facet's 21 and 22
Series of compact multi-purpose housings. The cartridge provides long
service life and high solids holding capacity with no unloading
characteristics. the filter cartridge removes solids from aqueous
liquids. Cartridges are 6" OD with outside to inside flow available
in two lengths and three micronic retention levels 2, 10 and 25 microns. |
|
|
 |
M Series High Efficiency Pleated Paper Filter Cartridges
Facet's M Series are excellent for
removing solid contaminants such as rust, dirt, scale, granular and
other types of solids from fuels. Media with efficiencies throughout the
life of the cartridges are available to the aviation market in micronic
ratings of 0.5 to 15µ nominal. These cartridges can be provided with
either a perforated paper or expanded metal outer wrap if required.
These 6" OD cartridges with outside to inside flow are available
nine micronic ratings and in three lengths; single, double( X2) and
triple (X3).
|
|
|
 |
M Series Multi-Media Pleated Filter Cartridges Facet's
multi-media, pleated, extended area, depth filter cartridges are for
removing colloidal, slimy or sludge type solids from process streams.
These 6" OD cartridges with outside to inside flow are available in
0.5, 1 and 2µ nominal retention ratings in three lengths.
|
|
|
 |
CIF Series Crushable Cartridges by Facet
significantly reduce waste volume for used cartridges and provide high
efficiency removal of solids and contaminants from fuel. Media with
efficiencies throughout the life of the cartridges are available to the
aviation market in micronic ratings of 1, 3 and 5µ nominal. We
recommend replacement when the differential pressure reaches 15 psi. To
use the CIF Series cartridge requires the one time installation of
either a single, double or triple-length center tube kit. each kit
contains all the hardware and components required to convert any housing
fitted for 6" OD x 3½" ID cartridges. Facet's
CIF Series cartridges are available in single, double (X2) and triple
(X3) lengths.
Not recommended for filtration of potable fluids.
|
|
|
|
|
 |
Wafer Repack Single-Stage Coalescers Facet
wafer repacks, used with Facet HP
Series Single-Stage Coalescer Housings, are excellent coalescers or
strainers for fuel applications when gross water contamination
conditions exist. Heavy solids or certain types of solids tend to either
blind off the surface of the repack media and/or compress only the first
and second wafers to the point that they will no longer function as a
coalescer. With Facet wafer repacks,
only the first two wafers need to be replaced when required while the
third and successive downstream wafers require fewer change outs since
they generally remain relatively free of solids.
|
|
|
|
|
I.P. Qualified |
21 and 22 Series Fuel-Gard® Monitor Cartridges meet
the latest edition of the Institute of Petroleum (I.P.) Specifications
and Qualification Procedures - Aviation Fuel Filter Monitors With
Adsorbent Type Elements. Facet
manufactures the cartridge with layered and pleated, multi-media
sections with inner support shells and an outer wrap. A special water
absorbent media retains water and the pleats expand. as the maximum
water holding capacity is reached, a reduction in flow occurs,
indicating the cartridge should be changed. The cartridge is available
in two lengths with outside to inside flow designed to allow less than
0.3 ppm (0.3 mg/liter) solids and less than 1 ppm of water in the
effluent.
|
|
|
I.P. Qualified |
FG Series Fuel-Gard® Monitor Cartridges 6" OD - Outside/Inside
Flow meet the latest edition of the Institute of
Petroleum (I.P.) Specifications and Qualification Procedures - Aviation
Fuel Filter Monitors With Adsorbent Type Elements. Facet's
monitor cartridges performs three jobs assuring clean dry
fuel. They absorbs free and emulsified water, remove ultra-fine solids
even when surfactants and fuel additives are present, and shut down the
system flow when hit with a localized slug of water. They are designed
to flow from the outside to inside at a rate of 4 gallons per inch of
length. The cartridge is available in four lengths, each designed to
allow less than 0.3 ppm (0.3 mg/liter) solids and less than 1 ppm of
water in the effluent.
|
|
|
I.P. Qualified |
FG Series Fuel-Gard® Monitor Cartridges 6" OD - Inside/Outside
Flow meet the latest edition of the Institute of
Petroleum (I.P.) Specifications and Qualification Procedures - Aviation
Fuel Filter Monitors With Adsorbent Type Elements. Facet's
monitor cartridges performs three jobs assuring clean dry
fuel. They absorbs free and emulsified water, remove ultra-fine solids
even when surfactants and fuel additives are present, and shut down the
system flow when hit with a localized slug of water. They are designed
to flow from the inside to outside at a rate of 4 gallons per inch of
length. The cartridge is available in eight lengths, each designed to
allow less than 0.3 ppm (0.3 mg/liter) solids and less than 1 ppm of
water in the effluent.
|
|
|
I.P. Qualified |
FG Series Fuel-Gard® Monitor Cartridges 2" OD - Outside/Inside
Flow meet the latest edition of the Institute of
Petroleum (I.P.) Specifications and Qualification Procedures - Aviation
Fuel Filter Monitors With Adsorbent Type Elements. Facet's
2" monitor cartridges performs three jobs assuring clean dry
fuel. They absorbs free and emulsified water to less than 5 ppm, remove ultra-fine solids
even when surfactants and fuel additives are present, and shut down the
system flow when hit with a localized slug of water. They are designed
to flow from the outside to inside at a rate of 1 gallon per inch of
length. The cartridge is available in six lengths, each designed to
allow less than 0.3 ppm (0.3 mg/liter) solids and less than 5 ppm of
water in the effluent.
|
|
|
MIL-M-
81380C(AS) |
GNG Series Go-No-Go Military Monitor Cartridges 2" OD -
Outside/Inside Flow meet the latest edition of the
Military Specification (MIL-M-81380C(AC) for Monitor, Contamination,
Aviation Fuel Dispensing Systems. Facet's
2" monitor cartridges performs three jobs assuring clean dry
fuel. They absorbs free and emulsified water to less than 2 ppm, remove ultra-fine solids
even when surfactants and fuel additives are present, and shut down the
system flow when hit with a localized slug of water. They are designed
to flow from the outside to inside at a rate of 1 gallon per inch of
length. The cartridge is available in six lengths, each designed to
allow less than 0.3 ppm (0.3 mg/liter) solids and less than 2 ppm of
water in the effluent.
|
|
|
I.P. Qualified |
PS Series Posi-Stop™ Fuel-Gard® Monitor Cartridge 2" OD - Outside/Inside
Flow meet the latest edition of the Institute
of Petroleum (I.P.) Specifications and Qualification Procedures -
Aviation Fuel Filter Monitors With Adsorbent Type Elements. Facet's
patented 2" Posi-Stop™ Fuel-Gard® Monitor Cartridge performs
four jobs assuring clean dry
fuel. They absorbs free and emulsified water to less than 5 ppm, remove ultra-fine solids
even when surfactants and fuel additives are present, and shut down the
system flow when hit with a localized slug of water, and positively shut
down system flow when pressure drop across the cartridge exceeds 40 psi
eliminating any possibility of media or water transmission while also
preventing the system being reused. The operator must
replace the elements before continuation of the fuel flow, thus ensuring
totally safe operation. They are designed
to flow from the outside to inside at a rate of 1 gallon per inch of
length. The cartridge is available in six lengths, each designed to
allow less than 0.3 ppm (0.3 mg/liter) solids and less than 5 ppm of
water in the effluent.
|
|
|
|
|
|
Meets API/IP 1583 effluent
requirements |
Fuel-Gard® Aviation Spin-On
Filters perform three jobs to give you
clean dry fuel. They adsorb free and emulsified water, remove
ultra-fine solids even when surfactants and fuel additives are
present, and shut down system flow when hit with a localized slug of
water. The filters are designed to flow at a rate of 13 gpm
(FGS-O-4050 and 15 gpm (FGS-O-409). A variety of head styles
and flow rates are available. Call us for more information. |
|
|
Teflon® is a registered trademark of E.I.
Dupont de Nemours Company (Inc.)
 |
Facet Aviation
Housings |
 |
 |
 |
 |
Facet Aviation
Cartridges |
 |
 |
 |
 |
 |
 |
|
Accessories |
 |
 |
 |
|
